Science & TechnologyLOT 261122 · 4 min read

KAIST and Caltech Crack Barium Titanate's Optical Mystery

KAIST and Caltech measured barium titanate's refractive index and absorption from 190 nm to 40 µm, settling decades of conflicting data and enabling lower-loss optical modulators.

By Rebecca Stone707 words

Key takeaways

  1. KAIST announced the results on November 8, 2026; the study appeared in ACS Photonics on October 20, 2026.
  2. Measurements covered wavelengths from 190 nm to 40 µm, ultraviolet to far-infrared.
  3. Extinction coefficients of roughly 10⁻⁵ were determined in the 2–10 µm range.
  4. The team used Mueller matrix spectroscopic ellipsometry on single-crystal BTO samples.
  5. Partners included KAIST, Caltech, KRISS and J.A. Woollam Co.
A decades-old mystery about light could hold the key to faster internet
A decades-old mystery about light could hold the key to faster internet — tiburi / pixabay

Researchers at KAIST and Caltech have precisely measured how barium titanate (BTO) controls and absorbs light, resolving uncertainties that have slowed the material's development for decades. Their measurements span wavelengths from 190 nanometers to 40 micrometers — ultraviolet to far-infrared — and pin down extinction coefficients of roughly 10⁻⁵ in the 2–10 µm range, where BTO lets nearly all incoming light pass through.

The work gives engineers a reliable reference for a material that could sharpen the performance of optical modulators, the components that convert electrical information into light-carried signals. KAIST announced the results on November 8. The study appeared online in ACS Photonics on October 20, 2026.

Why has barium titanate confused researchers for decades?

BTO's appeal rests on the Pockels effect: apply electricity and the material changes how it affects light. That strong electro-optic response makes it a candidate for modulators in advanced communication systems.

But designing real devices requires two numbers. The refractive index describes how light travels through a material; the extinction coefficient says how strongly the material absorbs it. Engineers need both to predict how light behaves inside a waveguide and how much signal gets lost.

Getting consistent values from BTO has been surprisingly hard. The crystal contains microscopic regions called domains, in which the structure points in different directions. Each domain interacts with light differently. Measurements of a whole sample therefore blend several distinct responses, and the result has been decades of widely conflicting reports on BTO's optical properties.

How did the team fix the measurement problem?

Professor Min Seok Jang of KAIST's School of Electrical Engineering led the research, working with Professor Harry A. Atwater's group at Caltech, the Korea Research Institute of Standards and Science (KRISS), and U.S.-based J.A. Woollam Co.

The team used Mueller matrix spectroscopic ellipsometry, a technique that tracks how light's polarization changes when it reflects from or passes through a material. Rather than fighting mixed-domain crystals, they studied two types of single-crystal samples with relatively consistent domain orientations, which minimized overlapping optical responses.

Because a material's optical behavior shifts with wavelength, the researchers split the spectrum into three regions and applied a different analytical approach to each. That revealed how BTO's refractive index and absorption depend on both wavelength and crystal orientation.

For the low-absorption window, they combined ellipsometry with separate transmission measurements and detected absorption so faint it yielded extinction coefficients of approximately 10⁻⁵ across 2–10 µm. Those values let engineers estimate how much light is lost as it travels through or stays confined inside optical components.

The team went one step further. They developed a method to predict the combined optical behavior of multi-domain crystals, using the domains' orientations and the proportion of the crystal each occupies to calculate the material's overall response to light.

What changes for device designers?

With accurate BTO data in hand, engineers can model how light will travel through components of different shapes and dimensions before manufacturing them. They can also better estimate absorption losses — potentially cutting repeated prototypes, costly redesigns and extensive testing.

The benefits could reach beyond conventional optical communications. BTO may also figure in devices that emit light at different wavelengths and in photonic circuits that process quantum information, technologies that hinge on controlling light with exceptional precision.

"This study reveals the optical response of barium titanate, which had long remained unclear, and provides a reliable reference for how the material interacts with light," said Professor Min Seok Jang. He added that the findings could contribute to optical communication devices that transmit data faster while reducing light loss.

Jiwon Kang, a Ph.D. candidate at KAIST's School of Electrical Engineering, and Dr. Nina Hong of J.A. Woollam Co. served as co-first authors; Jang and Atwater were corresponding authors. Funding came from Korea's Culture, Sports and Tourism R&D Program via KOCCA, the National Research Foundation of Korea's Basic Science Research Program, the Ministry of Science and ICT, and the U.S. Air Force Office of Scientific Research.

With a dependable optical baseline now published, BTO-based modulators and quantum photonic circuits move one step closer to predictable, manufacturable designs.

sciencedaily.com (Source)

Filed under

Share this article:

More from Rebecca Stone

Rebecca Stone

Show full bio

Correspondent covering technology and product news in Semiconductors, chip manufacturing, hardware, AI compute at Chip Dispatch.

1,245 articles

Read also

« Previous article